Precautions when operating the corn combine harvester
2021-06-09 12:02:37
1.Before the operation, the work component clutch should be smoothly integrated. When the throttle is from small to large, it is only at a stable rated speed before the harvest operation can begin.
2. The driver should observe and listen to the operation of various parts of the machine at any time during the work. If any abnormality is found, stop and extinguish the problem immediately and do not allow the machine to be sick.
3. When the chiller is turning, land transferring or long-distance vacancies and transportation, the harvester must be powered off.
4. Work first with a low I block test cut. If it works properly and then increase a gear properly, after harvesting for a certain distance, should stop checking the harvest quality, observe whether the adjustment of various parts is appropriate, no abnormal phenomena can enter the normal operation. In order to facilitate the unloading of food trucks and personnel, a lane was first opened in the middle of the ground, and then the land was cut off to make a turn for the land.
5. When working, check the quality of cutting and squeegee regularly and keep the height of the cutting, and adjust the height of the header at any time.
6. Clean the radiator and supplement the cooling water to prevent the engine water temperature from being too high.
7. When the engine cooling water temperature is too high, you should stop cleaning the radiator and add cooling water in time. However, do not open the tank cover immediately to avoid burns. After cooling for a certain period of time or after taking protective measures, open the tank cover and add cooling. water.
8. After working for a period of time, the work of the corn harvester should be interrupted for 1 to 2 minutes to allow the working parts to run empty so as to remove all remaining corn ear, kernels, etc. from the working parts, and to block the working parts. When the working part is blocked, it shall be stopped in time to clear the blockage, otherwise it will cause the friction of the corn combine harvester to increase, and the parts will be damaged.
9. Check the operation of the picking device based on the number of grains dropped on the ground. The loss of grain should not exceed 0.5% of the total corn kernels. When the loss is large, check whether the working gap between the picking boards is appropriate.
2. The driver should observe and listen to the operation of various parts of the machine at any time during the work. If any abnormality is found, stop and extinguish the problem immediately and do not allow the machine to be sick.
3. When the chiller is turning, land transferring or long-distance vacancies and transportation, the harvester must be powered off.
4. Work first with a low I block test cut. If it works properly and then increase a gear properly, after harvesting for a certain distance, should stop checking the harvest quality, observe whether the adjustment of various parts is appropriate, no abnormal phenomena can enter the normal operation. In order to facilitate the unloading of food trucks and personnel, a lane was first opened in the middle of the ground, and then the land was cut off to make a turn for the land.
5. When working, check the quality of cutting and squeegee regularly and keep the height of the cutting, and adjust the height of the header at any time.
6. Clean the radiator and supplement the cooling water to prevent the engine water temperature from being too high.
7. When the engine cooling water temperature is too high, you should stop cleaning the radiator and add cooling water in time. However, do not open the tank cover immediately to avoid burns. After cooling for a certain period of time or after taking protective measures, open the tank cover and add cooling. water.
8. After working for a period of time, the work of the corn harvester should be interrupted for 1 to 2 minutes to allow the working parts to run empty so as to remove all remaining corn ear, kernels, etc. from the working parts, and to block the working parts. When the working part is blocked, it shall be stopped in time to clear the blockage, otherwise it will cause the friction of the corn combine harvester to increase, and the parts will be damaged.
9. Check the operation of the picking device based on the number of grains dropped on the ground. The loss of grain should not exceed 0.5% of the total corn kernels. When the loss is large, check whether the working gap between the picking boards is appropriate.
Antigen Test Kit, Antigen Rapid Test Kit, Antigen Test Kit COVID, Antigen Diagnostic Test Kit, Swab Antigen Test Kit, Corona Antigen Test Kit
Antigen Test Kit, Antigen Rapid Test Kit, Antigen Test Kit COVID, Antigen Diagnostic Test Kit, Swab Antigen Test Kit, Corona Antigen Test Kit
Luck Medical Consumables Co.,LIMITED , https://www.luckmedical.com