Matters needing attention when using the powder tableting machine
2022-10-03 05:05:49
Zyzhan Guide : The powder tablet press is a small, basket-type continuous automatic tablet press. It is one of the necessary equipment for the processing of granular raw materials into tablets or granules in the pharmaceutical, food, electronics and other industrial sectors. It is suitable for small batch production, laboratory, hospital and other departments to suppress tablets, coal, sugar tablets, calcium tablets, coffee tablets, powder metallurgy, electronic originals and various agricultural fertilizer tablets. It can suppress a variety of shaped, ring-shaped tablets, and can suppress tablets with both trademarks, text and simple graphics on both sides.
1. Before starting the machine, the corresponding operating rules should be formulated according to the working principle and structural performance of each mechanism of the machine.
2. This machine is an extruded powder processing machine. The motor is integrated with the main unit, the structure is compact, the operation is safe and secure, and it can be normally consumed without fixing the device, but it should be placed on the flat and flat floor.
3. When the machine is turned on, the requirements should be stopped for all departments to check whether the machine parts are intact, whether the joints can be consolidated, whether the moving parts can be sensitive, and whether the smooth parts can be smoothed according to the rules. It is not necessary to adjust it. The direction of rotation of the pulley of this machine is: when the operator faces the pulley, it rotates counterclockwise. Test run for 10 minutes before starting normal consumption.
4, the largest particles in the powder should not be greater than 4mm, less than 2mm fine should not be more than 80, also participate in the appropriate amount of binder and sulfur-fixing agent, the moisture content of the raw material is about 12, should be dry and wet average no pinch phenomenon .
5, the work site should be carefully liquidated, the powder after crushing should be isolated from the original powder, it is strictly prohibited to mix iron, stone and other debris.
6. Regularly check the tightness of the pulley, the tightening and smooth condition of each component, and find that it is not handled properly. After the insurance is cut off, it is necessary to find out the cause and remove the problem before continuing to consume.
7. When adjusting the upper punch, add padding between the beam and the five-hole plate to prevent the beam from sliding down. The coal machine is not allowed to touch the moving parts when working.
8, no heavy-duty start, stop the coal first stop, stop the powder in the bucket after use, then stop the water, flush the upper assembly.
9. When the machine is shut down for a long time, it is necessary to cut off the power supply, remove the V-belt and the belt, clear and flush, and the moving parts are oil-wrapped.
10. It is not allowed to increase the speed of the coal machine pulley and the diameter of the insurance shaft to avoid damage to the machine and to form unnecessary losses.
1. Before starting the machine, the corresponding operating rules should be formulated according to the working principle and structural performance of each mechanism of the machine.
2. This machine is an extruded powder processing machine. The motor is integrated with the main unit, the structure is compact, the operation is safe and secure, and it can be normally consumed without fixing the device, but it should be placed on the flat and flat floor.
3. When the machine is turned on, the requirements should be stopped for all departments to check whether the machine parts are intact, whether the joints can be consolidated, whether the moving parts can be sensitive, and whether the smooth parts can be smoothed according to the rules. It is not necessary to adjust it. The direction of rotation of the pulley of this machine is: when the operator faces the pulley, it rotates counterclockwise. Test run for 10 minutes before starting normal consumption.
4, the largest particles in the powder should not be greater than 4mm, less than 2mm fine should not be more than 80, also participate in the appropriate amount of binder and sulfur-fixing agent, the moisture content of the raw material is about 12, should be dry and wet average no pinch phenomenon .
5, the work site should be carefully liquidated, the powder after crushing should be isolated from the original powder, it is strictly prohibited to mix iron, stone and other debris.
6. Regularly check the tightness of the pulley, the tightening and smooth condition of each component, and find that it is not handled properly. After the insurance is cut off, it is necessary to find out the cause and remove the problem before continuing to consume.
7. When adjusting the upper punch, add padding between the beam and the five-hole plate to prevent the beam from sliding down. The coal machine is not allowed to touch the moving parts when working.
8, no heavy-duty start, stop the coal first stop, stop the powder in the bucket after use, then stop the water, flush the upper assembly.
9. When the machine is shut down for a long time, it is necessary to cut off the power supply, remove the V-belt and the belt, clear and flush, and the moving parts are oil-wrapped.
10. It is not allowed to increase the speed of the coal machine pulley and the diameter of the insurance shaft to avoid damage to the machine and to form unnecessary losses.
Nosiheptide Feed Additives,Nosiheptide Antibiotics,Nosiheptide Growth Prompter,Nosiheptide Poultry
Shandong Shengli Bioengineering Co., Ltd , https://www.shenglipharm.com